Investigation of Mechanical Properties of FDM Materials Produced with SiO2 Reinforced PLA Filaments
Özet Görüntüleme: 191
/ 
PDF İndirme: 92
DOI:
https://doi.org/10.5281/zenodo.6948421Anahtar Kelimeler:
Silicon dioxide (SiO2), PLA (Polylactic acid) filament, FDM, 3D printer, Tensile test, Mechanical characterizationÖzet
Recently, FDM printers have taken their place in many places from workplaces to homes. Polymer-based filaments are used in these printers. The wide variety of polymers also increases the variety of products that can be used in FDM printers. For this reason, many studies are carried out in this field to ensure the production of parts with better mechanical properties, better surface quality and to use 3D printing capabilities in specific applications. In this study, the effect of SiO2 composition on PLA-based filaments on the mechanical properties of the materials produced using these filaments was investigated. SiO2 reinforced PLA filaments are produced with 10, 20 and 30 wt% SiO2 reinforcement. Tensile specimens with 100% fill rate and grid fill shape were produced from this composite filament. The test results showed that SiO2 reinforcement decreased the yield and tensile strength values and elastic modulus of the materials, but increased the toughness values.
Referanslar
Attaran, M. (2017). The rise of 3-D printing : The advantages of additive manufacturing over traditional manufacturing. Business Horizons, 60(5), 677–688. https://doi.org/10.1016/j.bushor.2017.05.011
Bacak, S., Varol Özkavak, H., & Tatlı, M. (2021). Investıgatıon of the effect of processıng parameters on tensıle propertıes of pla samples produced by fdm method. Journal of Engineering Sciences and Design, 9(1), 209–216. https://doi.org/10.21923/jesd.750264
Bedi, P., Singh, R., & Ahuja, I. P. S. (2018). Effect of SiC / Al 2 O 3 particle size reinforcement in recycled LDPE matrix on mechanical properties of FDM feed stock filament. 2759. https://doi.org/10.1080/17452759.2018.1496605
Dudek, P. (2013). Agh university of science and technology, faculty of mechanical engineering and robotics, al. a. mickiewicza 30, 30-059 kraków, poland. https://doi.org/10.2478/amm-2013-0186
Evlen, H., Özdemİr, M. A., & Çalişkan, A. (2019). Effects of filling percentage on mechanical properties of PLA and PET materials. 0900(4), 1031–1037. https://doi.org/10.2339/politeknik.426413
Günay, M., Gündüz, S., Yilmaz, H., & Yaşar, N. (2020). Optimization of 3D printing operation parameters for tensile strength in PLA based sample. JOURNAL of POLYTECHNIC, 23(1), 73–79. https://doi.org/10.2339/politeknik.422795
Ivanov, E., Kotsilkova, R., Xia, H., Chen, Y., Donato, R. K., Donato, K., Godoy, A. P., Maio, R. Di, Silvestre, C., Cimmino, S., & Angelov, V. (2019). applied sciences PLA / Graphene / MWCNT Composites with Improved Electrical and Thermal Properties Suitable for FDM 3D Printing Applications. https://doi.org/10.3390/app9061209
Jacobsen, S., Fritz, H. G., & Jerome, R. (1999). Polylactide (PLA)-A New Way of Production +. Polymer Engıneerıng and Scıence, 39(7), 1311–1319.
Kristiawan, R. B., Imaduddin, F., & Ariawan, D. (2021). A review on the fused deposition modeling ( FDM ) 3D printing : Filament processing , materials , and printing parameters. 639–649.
Kumar, A., Equbal, A., Toppo, V., Ohdar, R. K., & Mahapatra, S. S. (2012). CIRP Journal of Manufacturing Science and Technology An investigation on sliding wear of FDM built parts. CIRP Journal of Manufacturing Science and Technology, 5(1), 48–54. https://doi.org/10.1016/j.cirpj.2011.08.003
Letcher, T. (2015). IMECE2014-39379 Material property testing of 3D-printed specimen in pla on an entry-level 3D prınter. February. https://doi.org/10.1115/IMECE2014-39379
Liu, Wenbo, Wu, N., & Pochiraju, K. (2018). Shape recovery characteristics of SiC / C / PLA composite fi laments and 3D printed parts. Composites Part A, 108(October 2017), 1–11. https://doi.org/10.1016/j.compositesa.2018.02.017
Liu, Wenjie, Zhou, J., Ma, Y., Wang, J., & Xu, J. (2017). Fabrication of PLA Filaments and its Printable Performance Fabrication of PLA Filaments and its Printable Performance. 1–7. https://doi.org/10.1088/1757-899X/275/1/012033
Odent, J., Raquez, J. M., Hakim, R. H., Cailloux, J., Santana, O. O., Bou, J., S, M., Dubois, P., Carrasco, F., & Maspoch, M. L. (2017). PLA / SiO 2 composites : Influence of the filler modifications on the morphology , crystallization behavior , and mechanical properties. 45367, 9–11. https://doi.org/10.1002/app.45367
Öz, Ö., & Öztürk, F. H. (2022). Investigation of the effects of printing angle on mechanical properties of PLA specimen fabricated with 3D printer by using experimental and finite elements method. Journal of Polytechnıc, 1(1), 0–14. https://doi.org/10.2339/politeknik.882313
Popescu, D., Zapciu, A., Amza, C., Baciu, F., & Marinescu, R. (2018). FDM process parameters in fl uence over the mechanical properties of polymer specimens : A review. 69(May), 157–166. https://doi.org/10.1016/j.polymertesting.2018.05.020
Sodeifian, G., Ghaseminejad, S., & Akbar, A. (2019). Results in Physics Preparation of polypropylene / short glass fiber composite as Fused Deposition Modeling ( FDM ) filament. Results in Physics, 12(November 2018), 205–222. https://doi.org/10.1016/j.rinp.2018.11.065
Thiago, R., Ferreira, L., Amatte, I. C., & Daniel, B. (2017). Experimental characterization and micrography of 3D printed. May. https://doi.org/10.1016/j.compositesb.2017.05.013
Uzun, M., & Erdoğdu, Y. E. (2020). Investigation of the Effect of Using Unreinforced and Reinforced PLA in Production by Fused Deposition Modeling on Mechanical Properties. Journal of the Institute of Science and Technology, 10(4), 2800–2808. https://doi.org/10.21597/jist.799230
İndir
Yayınlanmış
Nasıl Atıf Yapılır
Sayı
Bölüm
Lisans
Telif Hakkı (c) 2022 Euroasia Journal of Mathematics, Engineering, Natural & Medical Sciences
Bu çalışma Creative Commons Attribution-NonCommercial 4.0 International License ile lisanslanmıştır.
Dergimizde yayımlanan makaleler, 